VXDIAG VCX SE Not Connect with Renault Clip V222 Solution

Problem:

I got the vxdiag vcx se with Renault active license. My Renault Clip 222 version cannot detect vxdiag cable. i need older or newer version or patch or something driver from vxdiag? i have no clue what problem is. Any advice?

Solution:

You need version V219.  The Renault driver is not ready for newer versions (V222/V237) yet.

1. Run Install Fix
2. Install SOFTWARE
3. Install Bosch Driver
4. Install VCI Driver
5. Registration SOFTWARE

Renault uses a separate VCI driver. Install the driver separately, you don’t need to install vx manager.

How to Update VXDIAG Benz VCI for 2024.09 Xentry?

VXDIAG Benz C6 and VCX SE DoIP updated Benz driver and VCI firmware to support Xentry 2024.09 software. Here we will show how to update VXDIAG VCX VCI firmware and driver, then connect to Xentry 2024.09.

Procedure:

1. Update firmware 

Connect VXDIAG VCX SE Benz or Benz C6 VCI with laptop.

Run VX Manager

Go to Device tab

Update Firmware

VX Manager detected there is a new version 1.9.6.0, press Upgrade and update VCI firmware until finish.

2. Update License

Update license

3. Update Benz C6 Driver

Go to Diagnostic Tab

Select Benz C6 drive

Uninstall old C6 driver.

Then install new C6 driver.

Disconnect VCX SE with laptop, then connect again.

VXDIAG VCX SE VCI is connected. Now you can use 2024.09 xentry software.

www.vxdiagshop.com

VXDIAG Benz VCI Firmware Update to 1.9.6.0

VXDIAG Benz C6 and VCX SE DoIP updated both C6 driver and VCI firmware to support 2024.09 Xentry software.

Benz C6 Driver

2024.08.27
Update: Xentry Diagnosis 09/2024 new version support
NOTE: This update requires the latest VCI firmware V1.9.6.0

To use 2024.09 Xentry you must update both C6 driver and VCI firmware to V1.9.6.0.

Connect vcx se benz or Benz C6 VCI with laptop

Run VX Manager

Update firmware- Update VCI and DoIP

Go to Diagnostic tab, Update Benz C6 driver

After update C6 driver, run Xentry recovery tool on the desktop to sync Xentry VCI.

Update firmware/VCI-> Update C6 driver-> Sync VCI.

www.vxdiagshop.com

VXDIAG Benz C6 No Device and Ping Failed Solution

Problem:

One of our customers had problems updating VXDIAG Benz C6 DoIP VCI firmware. When trying to update firmware, it says Connect device error: Ping failed. VX Manager can not see the C6 VCI (No device.)

Error attached:

Solution:

Ping failed error is usually related to the network.

Vxdiagshop.com technician did a check via Teamviewer and found he set the wrong IP manually for C6. That’s the IP for C4 SDConnect.

VXDIAG Benz C6 will automatically set IP address. Don’t need to change/set IP manually !!! 

Delete the wrong IP address.Then it will be fine. Now device is connected.

 If there is no network, follow the solution here:

 https://www.vxdiagshop.com/service/vxdiag-vcx-se-benz-connect-device-error-ping-failed-solution.html

VXDIAG 2TB HDD All Software Installed or Not?

Question

If I buy a 2TB VXDIAG hard drive is it supposed to have all the software brands on it?
all installed it set up and ready to be used?

Here is the clue.

Apart from Renault Clip, Ford and Mazda IDS software, all other software are pre-installed.

For GDS2, Toyota techstream, Subaru SSM4, Nissan Consult3 plus, Ford/Mazda IDS you need to start from patch.

GM GDS2/Tech2win: installed, but need to run software from patch

Toyota Techstream: installed, but need to run software from patch

Subaru SSM4: installed, but need to run software from patch

Honda HDS: installed, ready to use

VAG ODIS: installed, ready to use.

JLR SDD: installed, ready to use

Nissan Consult 3 plus: installed, but need to run software from patch

Ford/Mazda IDS: Not installed, need to install software and run from patch

Renault clip: Not installed, need to install software

PSA diagbox: installed, ready to use.

If you find software displays in Chinese, contact us to change language via Teamviewer.

Contact us if need 2TB software HDD or SSD only:

Skype:vxdiag.com
Email:[e-mail]
WHATSAPP:[phone]

WHATSAPP: [phone]