How to Fix VXDIAG GM GDS2 'Cannot Find File Specified'?

Here comes the problem: I've got the vxdiag vcx nano gm and u disk. I tried to install the software following the video guide but it failed me. When i run gm mdi manager, it says "Manager initialization error" and i tried to open GDS2 software, it threw another error "the system cannot find the file specified- t2w-proxy.jar". Any solution?

Solution:

1. You don't need to open GM MDI manager. It is just a driver for vcx nano gds2 device. Just got it installed.

2. Don't run GDS2 from GDS2 shortcut directly. Do Always run GDS2 from patch.

Easiest Way to Install both VXDIAG GM GDS2 & Tech2Win

VXDIAG IDS Adds Ford F150 2016 Keyless Entry Key

If your Ford F150 has no keyless entry/push-button start, it is possible to add that. Here is the instruction on how to add keyless entry remote start using dealer software.

It is not our work. Share for education purpose. You are at your risk.

Model example: F-150 XL year 2016

What you will need:

1. BCM from an IA equipped F150. I used part # FL3T-15604-AK
2. VXDIAG VCX Nano Ford or similar programming tool. You CAN NOT use a regular OBD device like you would use with Forscan, it HAS to be compatible with FDJS/FDRS/IDS
3. THE MOST IMPORTANT PART: Someone who has an IDS login.
4. Forscan
5. Driver Door Handle (Paint to match): FL3Z-1522405-GBPTM
6. Center Antenna: DS7Z-19D596-A
7. Rear Antenna: DS7Z-15603-D
8. Push button Start: DG9Z-10B776-AB
9. RTM: FL3Z-15607-L
10. Keys (x2) from Amazon
11. Male/Female pins. I used an old APIM connector for the female connectors, and had the 4 male on another connector. Should be able to lookup what the APIM uses to get the TE part number
12. Female pins for the antenna/door handle, I used 2.54mm dupont style connectors, something like this kit:
    
13. Wire
14. Optional:
    1. Push button start jumper harness: FL3Z-14A411-E
    2. Passenger door handle
    3. Tailgate handle
    4. Tailgate antenna
    5. Keyless entry pad on the door. If you don't have this already, do yourself a flavor and add it. More on that later….

Process:

1. Disconnect your battery when ever you are working with the BCM
2. BCM Connector Locations, keep in mind BCM is Upside down from picture, so C2280H is by the floor

3. Create the center antenna harness if your existing harness does not have the antenna runs. In my case with the XL and Jumpseat, I did not.

1. You will use connector C2280B at the BCM
   1. Pin 40 goes to Pin 1 on the Antenna
   2. Pin 27 goes to Pin 2 on the Antenna
2. I ran from the BCM up following a small harness across (behind the glove box) the A/C, down the right side of the radio under the carpet and pulled it up through the hole where the jump seat connector is (C3133 if looking at a diagram)
3. If you have the jump seat vs console, there is a provision for the antenna in the bottom plastic tray. You will want to flip up the bottom seat to access the storage area (aka the plastic tray) and remove the front two screws. The tray should lift up and out. Here is what it will look like with the antenna installed and back in place. I used a zip tie on each peg to hold it in place. I need to look into the proper hold down, probably a speed nut or the like as the zip ties came loose when plugging in the connector.

4. Create the rear antenna harness if you do not have it in the harness already. Mine did not. Something to note, I did not have this created nor hooked up originally, so technically this is not required, but probably a very good thing to have…

1. 1. Antenna goes on the back wall of the cab
   2. It connects to the BCM using connector C2280D
      1. Pin 16 goes to Antenna Pin 1
      2. Pin 15 goes to Antenna Pin 2

5. Create the drive door handle harness. Just like the rear antenna harness, I skipped this at first to make sure I could get the keyless start working.

1. 1. You will need to create two harnesses, one that goes between the BCM and the connector at the A pillar (Connector C510) and another that goes in the door.
   2. To go through the conduit between the A pillar into the door, I pulled out the rubber part from the door, removed the tape at the end and shoved a long rod through it with the wire taped to it. Once fished through, I re-taped it at the end and shoved it back in the door
   3. From the BCM to the A pillar, you will use the top of the two connectors, referred to as 'B'
      1. BCM Pin 13 to C510 B12
      2. BCM Pin 28 to C510 B13
      3. BCM Pin 20 to C510 B14
      4. BCM Pin 21 to C510 B15
   4. From the A pillar to the door handle
      1. C510 B12 to Handle Pin 2
      2. C510 B13 to Handle Pin 3
      3. C510 B14 to Handle Pin 4
      4. C510 B15 to Handle Pin 1

6. Create the push button start harness. I used the jumper wire listed in Optional and cut the end off

1. You will have 5 wires going to the BCM (Connector C2280A and C2280B) and 1 that just needs grounded, whether that's at the BCM or around the button area is up to you. I grabbed onto the metal plate that the OBD port bolts to. Also, the pin numbering for the pushbutton is AT THE PUSHBUTTON, do NOT get it confused on the jumper lead as they are pinned different.
   1. BCM C2280B Pin 51 to Pushbutton Pin 1
   2. BCM C2280B Pin 39 to Pushbutton Pin 2
   3. BCM C2280B Pin 45 to Pushbutton Pin 5
   4. BCM C2280B Pin 5 to Pushbutton Pin 6
   5. BCM C2280A Pin 12 to Pushbutton Pin 4 (I cut mine an inch or so back from the connect and spliced into it. The other end just goes to the keyed ignition so it can be left disconnected)
   6. Pushbutton Pin 3 to Ground
2. As far as mounting the Pushbutton, you can order the lower shroud with the hole, or like I did, drill a 1 3/8 (might be able to get by with 1 1/4) hole in your existing one

7. Once you have all the harnesses in place and they are connected to the antennas/handle(s)/Pushbutton (which can be done before you swap the BCM), it's time to swap in the BCM.

1. Before you disconnect your battery, use Forscan to backup your BCM as built data.
2. Disconnect the battery
3. Make sure you have one of the two keys in the special place Ford wants you to put it if your fob battery is dead. It's in the plastic try if you have the jumpseat (check your owners manual for specific placement)
4. If you bought a used BCM, make sure (don't ask me how I know…) to check ALL the fuses. I had a handful blown which led to programming frustration
5. Pull all the plugs on the BCM
6. Undo the screw and pull out the old BCM
7. Before installing new BCM, take a picture of the sticker on the back and pay special attention to the Key Code
8. Drop in new BCM and screw it down
9. Reconnect all connectors
10. Under the hood fuse box, unplug the horn relay
11. Reconnect the battery
12. This is where I said add the keyless entry pad if you don't already have it. The Ford instructions walk you through two ways of reprogramming the BCM
    1. Punch in the keycode (The one of the NEW BCM, not the old one) and make sure you hear it unlock the truck
    2. OR, if you don't have the keypad, you get to play the fun game of waiting 10 minutes and having 60 seconds at the end of it to program, and having to mess with opening the door at 4.5 minutes to make sure the alarm is still going off
13. Now is where you will connect up your programmer and laptop and have to run TWO operations, which not only require IDS/FDRS/FDJS, but an actual IDS login. So either have the dealership on board with this, or have someone remote in to program it.
    1. You will need to go into the program of choice and go into PATS operations
       1. You will need to delete and re-add keys as the first operation
          1. Go through the walkthrough and you should now have two keys programmed
       2. The second operation is the Parameter Reset, which cannot be run until the keys are programmed
    2. From here, you should be able to start the truck with the pushbutton, if not, something is wrong.

8. With the Keys programmed to the BCM and the Parameter Reset run, you will want to remove the the ignition tumbler so you do not have the steering lock up on you

9. From here, you will want to go in and update the BCM as built data to be a closer match to your truck than what it came out of. DO NOT simply load up your original As Built and write it as it will disable keyless components.

1. I used an as-built data compare tool to compare the as built of my original BCM to the new one, I don't remember everything I changed, but it was mainly things like lights since I don't have the upper level LEDs just the base model lights, and didn't have things like the 360 camera
2. Make sure to write your VIN number to the BCM, easiest to use the non-as built mode for that
3. Run "PCM: Module initialization and relearn vehicle data" in Forscan

Credit to nickstewartroc.

VXDIAG VCX SE Cannot Connect BMW Bike S1000RR?

Problem:

I got the vxdiag vcx se BMW with ista+ 4.32.15. It connects to an E46 car perfectly. But when comes to a BMW bike S1000RR build 2010 motorcycle, it asks to manually input VIN.

However it will not connect to bike after input vin, Any idea?

Connects with car ok

no communication with bike.

Solution:

VCX SE won't do 10-PIN BMW motorbike, standard OBD socket need luck. If your bike is 2017 onwards its OBD II. The 10 pin is the round one and its only for pre 2017 bikes.

For the older model you will need the ICOM D cable 10pin.

Check:

Will VXDIAG BMW scanners diagnose Motorcycles?

Free Download VXDIAG Ford and Mazda IDS V127

Allscanner new version Ford and Mazda IDS software V127 has been tested with vxdiag vcx nano ford, vcx se and vcx plus Ford scanner without issue.

Software version:

Ford IDS V127.01

Mazda IDS V127.01

Device affected: vxdiag vcx nano ford/mazda USB version, vxdiag vcx nano ford/mazda WiFi version, VXDIAG VCX SE Pro, VXDIAG Full, VXDIAG VCX Plus 3 in 1 etc

Operating system: Win7, Win8 and Win10

Attention: Mazda and ford ids must be installed on different operative systems. On the same computer but on different windows(dual boot) only. Or on different computers

Free download Ford IDS V127

https://disk.yandex.com/d/dN2AQzBpQ2zhng

File including:

IDS-127.01_full.exe
VCI_Software_1.0.0.10.exe

Free download Mazda IDS V127

https://disk.yandex.com/d/W13LJjMKxOP9LQ

File including:

IDS-127.00_full.exe

Mazda IDS software is only for 6th generation vehicles and earlier.

Free download Ford and Mazda IDS Patch

https://disk.yandex.com/d/721IaUrRmilL9A

ford ids native install languages: Chinese (traditional, simplified), Czech, Danish, Dutch, English, Finnish, French, German, Greek, Hungarian,

Italian, Japanese, Norwegian, Polish, Portuguese, Romanian, Russian, Slovenian, Spanish, Swedish, Thai, Turkish

Ford IDS Installation:

1. Install Ford IDS-1**
2. Wait for the installation of Ford IDS – 1**, and restart the computer
3. Install the Ford original VCI software_ 1.0.0.10.exe
4. Install VX manager and Ford IDS driver
5. Wait for VX manager and Ford IDS driver installation to complete
6. Connect VCX device and install idspatch
7. Use idspatch to open IDs and start diagnosis.

Mazda IDS Installation:

1. Install mazdaids-1**
2. Wait for mazdaids – 1** installation to complete and restart the computer
3. Install VX manager and Ford IDS driver
4. Wait for VX manager and Ford IDS driver installation to complete
5. Connect VCX device and install idspatch
6. Use idspatch to open IDs and start diagnosis.

VXDIAG VCX SE DoNet Device Connect Failed Solution

Problem:

I followed your instruction to set up DoNET remote diagnosis of my vxdiag vcx se pro device.

It failed me and says device connect failed.

Solution:

Network issue. Bad network connection.

Change IP or better network connection.

Feedback:

I changed my IP to Chinese IP. Now it is connected.